Move tmk_core/common/<plat> (#13918)

platforms/chibios/bootloader.c

@@ -0,0 +1,145 @@
+#include "bootloader.h"
+
+#include <ch.h>
+#include <hal.h>
+#include "wait.h"
+
+/* This code should be checked whether it runs correctly on platforms */
+#define SYMVAL(sym) (uint32_t)(((uint8_t *)&(sym)) - ((uint8_t *)0))
+#define BOOTLOADER_MAGIC 0xDEADBEEF
+#define MAGIC_ADDR (unsigned long *)(SYMVAL(__ram0_end__) - 4)
+
+#ifndef STM32_BOOTLOADER_DUAL_BANK
+#    define STM32_BOOTLOADER_DUAL_BANK FALSE
+#endif
+
+#ifdef BOOTLOADER_TINYUF2
+
+#    define DBL_TAP_MAGIC 0xf01669ef  // From tinyuf2's board_api.h
+
+// defined by linker script
+extern uint32_t _board_dfu_dbl_tap[];
+#    define DBL_TAP_REG _board_dfu_dbl_tap[0]
+
+void bootloader_jump(void) {
+    DBL_TAP_REG = DBL_TAP_MAGIC;
+    NVIC_SystemReset();
+}
+
+void enter_bootloader_mode_if_requested(void) { /* not needed, no two-stage reset */
+}
+
+#elif STM32_BOOTLOADER_DUAL_BANK
+
+// Need pin definitions
+#    include "config_common.h"
+
+#    ifndef STM32_BOOTLOADER_DUAL_BANK_GPIO
+#        error "No STM32_BOOTLOADER_DUAL_BANK_GPIO defined, don't know which pin to toggle"
+#    endif
+
+#    ifndef STM32_BOOTLOADER_DUAL_BANK_POLARITY
+#        define STM32_BOOTLOADER_DUAL_BANK_POLARITY 0
+#    endif
+
+#    ifndef STM32_BOOTLOADER_DUAL_BANK_DELAY
+#        define STM32_BOOTLOADER_DUAL_BANK_DELAY 100000
+#    endif
+
+extern uint32_t __ram0_end__;
+
+__attribute__((weak)) void bootloader_jump(void) {
+    // For STM32 MCUs with dual-bank flash, and we're incapable of jumping to the bootloader. The first valid flash
+    // bank is executed unconditionally after a reset, so it doesn't enter DFU unless BOOT0 is high. Instead, we do
+    // it with hardware...in this case, we pull a GPIO high/low depending on the configuration, connects 3.3V to
+    // BOOT0's RC charging circuit, lets it charge the capacitor, and issue a system reset. See the QMK discord
+    // #hardware channel pins for an example circuit.
+    palSetPadMode(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_MODE_OUTPUT_PUSHPULL);
+#    if STM32_BOOTLOADER_DUAL_BANK_POLARITY
+    palSetPad(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO));
+#    else
+    palClearPad(PAL_PORT(STM32_BOOTLOADER_DUAL_BANK_GPIO), PAL_PAD(STM32_BOOTLOADER_DUAL_BANK_GPIO));
+#    endif
+
+    // Wait for a while for the capacitor to charge
+    wait_ms(100);
+
+    // Issue a system reset to get the ROM bootloader to execute, with BOOT0 high
+    NVIC_SystemReset();
+}
+
+void enter_bootloader_mode_if_requested(void) {}  // not needed at all, but if anybody attempts to invoke it....
+
+#elif defined(STM32_BOOTLOADER_ADDRESS)  // STM32_BOOTLOADER_DUAL_BANK
+
+extern uint32_t __ram0_end__;
+
+__attribute__((weak)) void bootloader_jump(void) {
+    *MAGIC_ADDR = BOOTLOADER_MAGIC;  // set magic flag => reset handler will jump into boot loader
+    NVIC_SystemReset();
+}
+
+void enter_bootloader_mode_if_requested(void) {
+    unsigned long *check = MAGIC_ADDR;
+    if (*check == BOOTLOADER_MAGIC) {
+        *check = 0;
+        __set_CONTROL(0);
+        __set_MSP(*(__IO uint32_t *)STM32_BOOTLOADER_ADDRESS);
+        __enable_irq();
+
+        typedef void (*BootJump_t)(void);
+        BootJump_t boot_jump = *(BootJump_t *)(STM32_BOOTLOADER_ADDRESS + 4);
+        boot_jump();
+        while (1)
+            ;
+    }
+}
+
+#elif defined(GD32VF103)
+
+#    define DBGMCU_KEY_UNLOCK 0x4B5A6978
+#    define DBGMCU_CMD_RESET 0x1
+
+__IO uint32_t *DBGMCU_KEY = (uint32_t *)DBGMCU_BASE + 0x0CU;
+__IO uint32_t *DBGMCU_CMD = (uint32_t *)DBGMCU_BASE + 0x08U;
+
+__attribute__((weak)) void bootloader_jump(void) {
+    /* The MTIMER unit of the GD32VF103 doesn't have the MSFRST
+     * register to generate a software reset request.
+     * BUT instead two undocumented registers in the debug peripheral
+     * that allow issueing a software reset. WHO would need the MSFRST
+     * register anyway? Source:
+     * https://github.com/esmil/gd32vf103inator/blob/master/include/gd32vf103/dbg.h */
+    *DBGMCU_KEY = DBGMCU_KEY_UNLOCK;
+    *DBGMCU_CMD = DBGMCU_CMD_RESET;
+}
+
+void enter_bootloader_mode_if_requested(void) { /* Jumping to bootloader is not possible from user code. */
+}
+
+#elif defined(KL2x) || defined(K20x) || defined(MK66F18) || defined(MIMXRT1062)  // STM32_BOOTLOADER_DUAL_BANK // STM32_BOOTLOADER_ADDRESS
+/* Kinetis */
+
+#    if defined(BOOTLOADER_KIIBOHD)
+/* Kiibohd Bootloader (MCHCK and Infinity KB) */
+#        define SCB_AIRCR_VECTKEY_WRITEMAGIC 0x05FA0000
+const uint8_t              sys_reset_to_loader_magic[] = "\xff\x00\x7fRESET TO LOADER\x7f\x00\xff";
+__attribute__((weak)) void bootloader_jump(void) {
+    void *volatile vbat = (void *)VBAT;
+    __builtin_memcpy(vbat, (const void *)sys_reset_to_loader_magic, sizeof(sys_reset_to_loader_magic));
+    // request reset
+    SCB->AIRCR = SCB_AIRCR_VECTKEY_WRITEMAGIC | SCB_AIRCR_SYSRESETREQ_Msk;
+}
+
+#    else /* defined(BOOTLOADER_KIIBOHD) */
+/* Default for Kinetis - expecting an ARM Teensy */
+#        include "wait.h"
+__attribute__((weak)) void bootloader_jump(void) {
+    wait_ms(100);
+    __BKPT(0);
+}
+#    endif /* defined(BOOTLOADER_KIIBOHD) */
+
+#else /* neither STM32 nor KINETIS */
+__attribute__((weak)) void bootloader_jump(void) {}
+#endif